Complete Electrical Design Training Course

Complete Electrical Design Training
Fee: 40,000

Duration: 3 Months

Timing:  9AM-11AM, 11AM-1PM, 1PM-3PM, 3PM-5PM, 5PM-7PM, 7PM-9PM

Complete Electrical Design Course Outline

  • COMPLETE ELECTRICAL DESIGN TRAINING COURSE
  • AutoCAD Electrical basics and Professional commands.
  • NO contact, NC contact, Relay Coil, Timer coil, NO push button, NC push button, SP MCB:
  • Copy and paste attribute symbols into palate and design center
  • Discus types of electrical diagram
  • How to make lighting distribution board (LDB) for story building
  • Draw DB diagram with respect to different types of load. (SLD and power circuit & calculation)
  • Load Balancing
  • SLD of DB checking/finishing and discussion
  • Draw SLD of motor control center (MCC), motor calculation & selection method of motor components
  • SLB MCC diagram checking/finishing and discussion
  • Study and understand DOL circuit and operation
  • DOL starter diagram (used attribute & Dynamic blocks for control circuit)
  • Study and understand ASD circuit and operation
  • ASD starter diagram (used attribute & Dynamic blocks for control circuit)
  • Study and understand REV/FOR circuit and operation
  • REV/FOR starter diagram (used attribute & Dynamic blocks for control circuit)
  • Checking schematic diagram of DOL, ASD & REV/FOR starters / fishing and discussion
  • Overview about all international standard relevant to electrical switchgear field
  • Types of switchgear panels (slides), Types of diagram (slides)
  • ANSI protection relay codes
  • Switchgear device/components codes
  • Draw the SLD & Schematic diagram of interlocking between 3 –motors with operating water level switch23. Checked schematic & control circuit of motor interlocking/fishing and discussion
  • Draw SLD, Schematic & diagram and interlocking of WAPDA & Generator source with using TP ACBs (25. Draw PFI diagram (SLD and power circuit)
  • PFI diagram discussion and Calculation for Power factor bank.
  • Wiring diagram of LT Switchboard
  • Copper bus bar calculations
  • ATS (Automatic Transfer Supply) Control Power diagram and Selection criteria.
  • Transformer and Generator size calculation and Proposal
  • Motor Control Center sizing i.e. Breaker sizing according to NEC , Contactor sizing, overload relay sizin
  • DOL, DOL 2 location, DOL long distance
  • DOL Reverse Forward
  • Star Delta
  • Reverse Forward star delta
  • Series Resistance Method
  • Series Inductance Method
  • Auto transformer Method
  • Buzzer and Light indication for faults
  • CT and PT calculation
  • Cable sizing and BS/NEC standard for voltage drop of cable selection.
  • Short circuit current calculation for breaker and cable selection
  • Introduction to industrial panels
  • Panel components
  • Transformers
  • Power Supply
  • Circuit Breakers
  • Disconnect Switch
  • Terminal Blocks
  • Relays
  • Contactors
  • Overload Relay
  • Fuses
  • Panel layout and design
  • Enclosure type and sizing
  • Power and circuit protection
  • Control components
  • Operator interface
  • Motor Drives
  • VFD
  • Motor Forward reverse run
  • Motor Starters
  • Star delta
  • DOL
  • Cable selection and size calculation
  • Panel wiring
  • Programmable Logic Controller (PLC)
  • Safety and regulations
  • Panel maintenance
  • LV Panels
  • LV Metering Panel
  • Synchronization
  • ATS with Auto Generator Sulf
  • Main Panel and Sub Main Panel
  • Generator Panel
  • Relay Panel
  • Power Factor Improvement Panel
  • LT Switchboard with different incomings
  • ACB
  • HV Panels
  • 11KV Protection Panel
  • 11KV Switchboard Incomings and Outgoing Panels.
  • Breaker Sizing for 11KV Line (Transformer Primary)
  •  VCB
  • Butchels Relay
  • Distance Relay
  • CDG 112 Relay
  • Relays Panel and Relays connections
  • Different types of switching relays
  • Home Wiring/Building Wiring
  • Test for Building Wiring
  • Continuity test
  • Short circuit test
  • Open circuit test
  • Earth Leakage Test
  • Polarity test
  • Home wiring Principles and rules according to IEE Rules and Regulation
  • Test with Mustimeter, Series test lamp and Mugger for Home or Building
  • Home wiring circuits and its applications
  • One Lamp control
  • Two Lamp in Parallel
  • Two Lamps in series
  • Staircase circuit
  • Tunnel circuit
  • Tube lights circuits
  • Series test Lamp
  • Panel testing using series test lamp or two lamp in series
  • Testing of all circuits and practical’s of all circuits
  • DB Design/Power DB Design SLD for multi storage building
  • Single Line Diagram of Sub Main Panel /Main Panel
  • ATS Panel
  • Lighting Calculation, Lighting design and lighting plan with DIALUX
  • Earthling and Grounding according to NEC Article 250
  • Tower Calculation for Lighting Arrestor
  • Cable Selection and format of reading a cable according to BS/NEC/IEC
  • Load scheduling Transformer selection and Generator selection and Main bus bar selection
  • Building/Home/Room Layout for lighting, fans or other equipment’s on design.
  • LAYOUT Plan Drawings reading and working and conduit LAYOUT
  • BOQ and SOP
  • Cables and glands types
  • SPDs and Lighting arrestors
  • Cable Trays
  • CCTV System
  • Fire Alarm System
  • Important Documents
  • Cable schedule
  • Material take off list
  • ETAP Software Installation
  • Introduction to ETAP Software
  • How to Create a New Project in ETAP
  • How to Load the existing Project
  • ETAP toolbar introduction
  • One Line Diagram in ETAP
  • Create your first one line diagram
  • Composite Network in ETAP
  • Creating a template and importing it to one line diagram
  • Load Flow Analysis
  • Run Load Analysis on Single Line Diagram
  • Voltage Drop Calculations
  • Bus Voltages, Cable voltage Drops
  • Bus Under voltage
  • Cable overload
  • Transformer Overload
  • Alert View in ETAP
  • Critical and Marginal Conditions in ETAP
  • Arc Flash and Short Circuit Analysis
  • Run Short circuit and Arc Flash Analysis
  • Short Circuit Current Evaluation
  • How to Fault a bus
  • Edit Study Case
  • Motor Start Analysis
  • Setting up the Motor Rating
  • Motor Start static
  • Setting up the Motor Events in Edit Study Case
  • Starting Current and its Plot in ETAP
  • Motor Start Dynamic
  • Setting up the Motor Parameters
  • Setting up the Motor Inertia, Load
  • Motor Start Dynamic using VFD
  • Protective Device Coordination Study
  • Breaker Settings
  • CT settings
  • Over current Relay Settings
  • Sequence of Operation
  • How to generate report on ETAP
  • Introduction to ETAP Level 2 Training
  • 167. Introduction to course
  • Introduction to ETAP Toolbar
  • Rating Components
  • Presentation Toolbars
  • Harmonic and Transient stability analysis
  • Ground Grid System
  • Cable Pulling System
  • Underground raceway system
  • Cable ampacity
  • Protective Device co ordination
  • Protection Schemes
  • Bus bar Differential Protection
  • Transformer differential Protection
  • Motor Protection
  • Directional Overcurrent Protection
  • Over and under voltage Protection
  • Over and under frequency protection
  • Reverse Power Protection
  • Revision and wizard toolbar
  • DC Load Flow
  • Battery sizing calculation
  • Solar Power System
  • Wind Power System
  • Advance Power system study
  • Optimal Power flow and Unbalanced load flow
  • Optimal capacitor placement
  • Switching sequence management
  • Final Project
  • Industrial Electrical Controls-Design and Installation
  • Basics of Relays, Contactor, MCB, MCCB, ELCB, ACB, VCB etc.
  • Working Details of Different Types of Electric Motors
  • Designing of Control Circuits Using Contactors, Relays, and Timers etc.
  • Star Delta Starter Designing for 3 Phase Motors with Specification
  • Practical Wiring Session on Different Controls
  • Motor Drives – AC Drives VFD à Parametering , Motor Operations
  • Safety and Management Concepts of Designing a Project
  • MCC DESIGN
  • Breaker sizing , Overload Relay Setting and Sizing, Contactor sizing, Busbar Sizing,
  • SUBSTATION DRAWINGS SLD
  • AUTOCAD for drawings Preparation
  • Power and Control Drawings
  • Protection Relays
  • Breaker and Relay Testing
  • Panel Layout Design
  • Control Panel Designing
  • Different Types of Panels
  • Basic Components to be Installed in a Panel
  • Wiring Details of Panel
  • Specification and Physical Dimension of Components
  • Earthing and Cabling of Panels – Standard Procedures
  • Types of drawings and its implementation
  • In this course we will provide all materials and equipment.
  • Overview of different VFD’s Fuji, INVT, and Danfoss and Schneider
  • Selection of VFD for Motor
  • Source of Freq.in VFD
  • Source of Operation in VFD
  • Jog Mode of Operation in VFD
  • Multiple Sources of Frequency in VFD
  • Disable the Reverse Operation of Motor?
  • How to Secure/Lock your Parameter?
  • Multi-step Speed Commands in VFD
  • Acceleration & Deceleration Time & Speed Inhibit
  • How to Bound the Frequency of Drive (Upper Bound & Lower Bound Function)
  • How to Reset the External Fault in Drive
  • How to change External Control of VFD
  • VFD Operational Feedback (ON/OFF)
  • Reading feedback of getting Desired Frequency in VFD
  • VFD Biasing
  • Biasing the Frequency
  • Biasing the Frequency with Pot. Freq. Gain
  • Biasing the Voltage
  • Acc./Dec. Time 1 (Default)
  • Acc./Dec. Time 2 (Conditional)
  • Introduction to Scaling
  • Wiring and Installation of VFD
  • Motor Speed Control using Built-in Potential.
  • Motor Speed control using Keypad of VFD
  • Motor Speed control using 0-10V (Analog Values)
  • Motor Speed control using 0-20mA (Analog Values)
  • Motor Max and Min Frequency set/reset
  • VFD Overload activation for Motor Protection
  • Motor Reverse Forward using functions.
  • Advance Functions
  • Two Motors On/off using One VFD
  • Motor Speed Control through Thermocouple (Analog Sensor)
  • Motor Reverse Forward using external signals.
  • Synchronization of two VFD’s (TEXTILE MILL Examples)
  • Complete wiring of VFD
  • Wiring of Analog sensors with VFD
  • Introduction to solar system and Solar System Installation
  • PV Array and its types
  • Mono Crystalline vs poly Crystalline
  • Intro to PVSYST software
  • PV system major parts
  • PV modules (groups of PV cells), which are commonly called PV panels
  • Batteries
  • Charge regulator or controller for a stand-alone system
  • Inverter
  • Wiring
  • Mounting hardware or a framework.
  • Panel mountings and their types
  • Rail-based mounting system.
  • Ballasted mounting system.
  • Anchored mounting system.
  • Residential roof.
  • Standing-seam mounting system:
  • Corrugated roof mounting system.
  • Fully-railed system or Shared-rail system.
  • Rail-less mounting system.
  • Pv system types
  • Grid-tied system
  • Grid-tied system with battery back-up
  • Off-grid system
  • Solar system installation considerations
  • Load calculations
  • Panel size calculations
  • Battery types and size calculations
  • Charge controller types and selection
  • PWM vs MPPT controllers
  • Inverter types and selection calculation
  • Battery-based Inverter/Charger
  • Introduction to DIALUX Software
  • How to Create Project in DIALUX and Project Settings
  • Interface of DIALUX (like bars, buttons, objects, Lighting catalog, room editor, the guide etc.)
  • Rectangular Room Lighting Design
  • How to install Plugin and IES File
  • Lighting Design in L-Shape Room
  • How to Import CAD file in DIALUX
  • Lighting Design of Rectangular Room using CAD File
  • Lighting Design of Polygonal Room using CAD File
  • Corridor Lighting Design using CAD File
  • Emergency Lighting Design
  • Wall Mounted Lighting Design
  • Street Lighting Design
  • Stadium Lighting Design
  • Lighting Design using Blue Icon
  • False Color Display and Objects in Room
  • Perform all lighting calculation using DIALUX software
  • Studying all types of lighting and choice of these types
  • Studying all types of interior lighting
  • Studying all types of exterior lighting
  • Studying all lighting drawings and the quality, intensity and viewing
  • Performing lighting analysis reports
  • Full project exercise
  • SOFTWARES INCLUDED
  • ETAP—AUTOCAD—PVSYS—REVIT—DIALUX EVO
  • BENEFITS: WORK ON A TENDER PROJECT
50% OFF ON ALL COURSES OF ELECTRICAL AND AUTOMATION AND IT Except Bootcamp Courses
This is default text for notification bar